Des +44 (0) 7871 877 061

Off The Cuff Bespoke Trousers

Waistband extension should be sharp, and STRAIGHT 14 May, 2014

Bespoke Trousers

This post is about bespoke trousers. Let me tell you, making good quality and well fitted bespoke trousers is not as easy as you think. How many times have you seen men that have a fairly decently fitted coat ? But lousy fitting trousers with a mega baggy bottom ? The big garment manufacturers struggle to make a half decent pair of well fitted trousers. So how can ‘Bill’ the local cheap tailor down the road come anywhere near making you a half decent pair of trousers ?

bespoke trousers

A bespoke trouser leg before shaping.

I believe men are now at the stage where they care what their suit looks like. They are actually looking at the seat of their trousers. There was a time when men never looked at the rear of their trousers. And to be honest it was a good job they didn’t. If they had, they may well have had a heart attack with the state of the trousers at the back !

Obviously, trousers need to be cut right. But more importantly they need a liberal use of the tailors iron, and I mean liberal. Not the type of liberal that knocks on your door asking you to vote for them. The heavy tailors iron plays the deciding role in the outcome of the fit and hang.

The picture to the right shows a bespoke trouser leg laid on my vac table before setting. You can see my two irons, a normal steam iron, and my 16lb heavy tailors pressing iron. If you look at the trouser at this stage you can see the leg is actually quite shapeless and rather parallel.

Bespoke trousers

Bespoke trouser partially shaped out by me.

The picture to the left shows the same trouser leg. But this time the picture shows the leg partially shaped with the heavy iron that you can also see in the picture. I have stretched and shrunk the cloth at the crucial places on the trouser and set the trouser creases front and rear.

Trousers when worn, should hang straight down at the back of your legs and fit nicely around the seat of your ……. err ……. arse !

There should be no creases, folds, pulls, drags or whatever more terminology I can use to describe an abomination of badly fitting trousers.

If you paid good hard cash for someone to make you so-called bespoke, or made to measure trousers and your trousers posses any of the above symptoms, then in a heart beat high tale it back to said twit from whence they came and demand they sort them out for you because they are not right. Don’t be shy in asking, nay, downright demand they rectify the problem, then maybe the outcome is that you will have them rumbled as a non tailor. ” Luke, I feel many refunds coming on within the Empire”

bespoke trousers

A little more shaping done.

Bespoke Trousers

The picture to the right shows clearly now the effect the iron has had on these trousers. Don’t even dream of asking me to explain pressing to you sunshine ! I can’t, it’s a feel a touch a clear understanding of the medium you are working with. It’s like a Samurai in a state of Zen before he goes into battle. It’s like me before I take the head off a pint of John Smiths cask bitter from my local …….. Where are we at ?

Ah yes, pressing, in a nutshell it’s down to EXPERIENCE and lots of it, simple.

The picture on the right shows the left trouser leg looking down it. The front of the trousers is to the bottom of the picture, ( no zip added yet ) and the seat of the trouser is to the top of the picture.

bespoke trousers

Trouser leg fully shaped out.

The picture on the left now shows you the leg fully shaped out. You can see the impression of the full leg inlay showing on the seam in the middle of the trouser leg, I ‘blow’ this impression out later when the trousers are finished when I will then fully press them off.

The fold or bump you can see is the leg lining and the pocket bag sitting inside the trouser leg.

If you compare this picture to the first picture in the article, then I hope you can see the difference through the sequence of pictures.To get the bespoke trousers to this stage. The trousers have gone from being fairly flat to something that actually resembles a leg and the backside of a man.

Incidentally, these trousers are now finished and are for a client of mine in London. He is tall and very lean. Tall men are obsessed with trousers being too short and too narrow.

bespoke trousers

Trouser hem should not show ANY STITCHING whatsoever !

LOOK at your trouser hems ! The hem shouldn’t have any stitches showing through when it is finished. If you can see the stitches then its been finished by machine, and badly done.

The picture to the left shows a portion of the top section of the bespoke trousers.

You can see in this picture the ‘extension’ portion of the left front waistband laid on my bunch of Fyffes bananas. The extension is as clean as you like, its square and straight. The run into the top of the waistband is also straight, as is the seam portion onto the actual trouser.

You can also see the zip, bespoke tailors use metal zips not PLASTIC !! Unless the cloth is a very lightweight cloth we may use a plastic zip. If you look closely you can also see the hand stitching down the front portion of the trouser.

If you have, then get your hat and coat on and beat a path back to the ‘tailor’ ! For more information look on my website desmerrion.com

Interested in a Consultation?

    Des +44 (0) 7871 877 061